Error Codes Canon iR3300 Code E003-0000

Code: E003-0000

Canon iR3300

• Description:The main thermistor reading is lower than 140C when paper is moved
• Causes:The fixing film unit is faulty (i.e., the main thermistor (TH1) has poor contact or has an open circuit; or, the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
• Remedy:1. State Turn on the power switch, and clear E002/E003. Thereafter, turn off and then on the power switch. Does the fixing heater operate? NO: See “The fixing heater fails to operate.” 2. Wiring Is the wiring from the DC controller PCB to the fixing film unit normal? NO: Correct the wiring. 3. Fixing film unit, DC controller PCB Try replacing the fixing film unit. Is the problem corrected? YES: End. NO: Replace the DC controller PCB.

How to fix Canon ir3300 error code e000000-0000

ow to fix Canon ir3300 error code e000000-0000. E00000 error Code refers to the copier fusing warm-up trouble. The fixing temperature does not reach 100 C with 2 min after it has exceeded 70 C. Fuser code needs to be reset in the service mode but if the problem persists after being cleared then the fuser may need to be rebuilt or replaced.

Canon IR 3300 series error code e000000-0000 problem solutions

Are you getting the error e000000-0000 on your Canon iR3300 copier? This should solve your problems. This introduction will help you to troubleshoot some common error code E000001-00000; E000001-0002 messages related to Canon iR2200, iR2800, and iR3300 series. If that is the case consider the following.

Meaning of the error code e000000-0000

E00000 error Code refers to the copier fusing warm-up trouble. The fixing temperature does not reach 100 C with 2 min after it has exceeded 70 C. Fuser code needs to be reset in the service mode but if the problem persists after being cleared then the fuser may need to be rebuilt or replaced.

How to fix the error code?

Do not try to change any settings in service mode or clear any other function!! It is very easy to turn the machine into a cabbage. Follow the steps below:

1. Press the “Additional Functions (*)” button once.
2. Then press the “2” and “8” buttons at the same time once.
3. Press the “Additional Functions (*)” button once again.
4. The System Management screen will open. Touch the “COPIER” button on the screen.
5. Touch the “FUNCTION” button at the top of the screen.
6. Touch the “CLEAR” button on the screen.
7. Touch the “ERR” button to highlight it.
8. Click the “OK” button at the bottom of the screen.
9. Then switch off the machine and turn the power back ON at the power socket and the code should reset. The machine will process for 2 minutes.

Even if the above fixes are shown in error code. Then check these all things.

Some possible cause:

• Check fixing unit:
• The thermistor has poor contact.
• Replace the heater element.
• Replace the thermal switch.
• Check the fixing assembly connecter.
• The SSR is faulty.
• DC controller is faulty

After you replace the parts, then you have to reset the machine in services mode COPIER

How to Clear Error Code e000007 for Canon iR3300 Series Copier

Error Codes > Canon > iR3300 > Code E007-0000

Code: E007-0000

COPIER>FUNCTION>CLEAR>ERR

Meaning of the E00007 Error Code?

The E0007 error Code refers to fixing film rotation issues. The fuser film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven. switch off the machine and turn the power back ON in the right, if the problem did not solve, so please the steps below.

How to Clear Error Code e000007 for Canon iR3300 Series Copier. The E0007 error Code refers fixing film rotation issue. Fuser film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven. switch off machine and turn the power back ON in the right, if the problem did not solve, so please the steps below.

Description:An error in the rotation of the fixing film is detected.
The reading of the main thermistor is 100C or higher and, in addition, the fixing film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven

Causes:

The fixing film sensor (PS45) is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR